What a Metallic Epoxy Floor Costs, and Why
A metallic epoxy floor runs about $7 to $14 per square foot in this market, which is roughly double a flake floor of the same size. A 500 square foot room lands around $3,500 to $7,000. Those are Kansas City market ranges, not a quote. What your floor costs is decided by the condition of the slab, and nobody can see that from a photograph.

The material is not what doubles it. A metallic pour is a one shot job with a working window measured in minutes, and you are paying for the labour inside that window and the risk of being wrong.
What are you actually paying for?
Time under pressure. Once the pigmented clear goes down it stays workable for a limited period, and everything that makes the floor look like anything happens in that period. Pouring, drawing, blowing, feathering the edges. Two people working a room continuously with no option to stop and come back tomorrow.
You are also paying for a flat slab. A self levelling pour finds every dip in the concrete and sits deeper there, which reads as a dark patch once it cures. Levelling before the pour is not optional on a metallic and it is a bigger part of this job than of any other finish.
Bring a picture of a floor you like. Glen will tell you honestly how close we can get and what it would cost.
How a metallic pour is madeHow does it compare to the other finishes?
| Finish | Typical per sq ft | Best for |
|---|---|---|
| Solid colour | $4 to $7 | A clean single tone in a room that is kept rather than worked. |
| Full flake broadcast | $4 to $8 | Garages and anywhere that needs grip and needs to hide wear. |
| Quartz broadcast | $6 to $11 | Commercial and industrial. Hardest and grippiest of the four. |
| Metallic | $7 to $14 | One room people walk into and look at. |
What is the catch?
You cannot sample the pattern. You can see the palette and you can see the depth on other floors, and the actual movement on your slab is made on the day by how the resin behaves in your room at your temperature. If an exact repeatable pattern matters to you, a metallic is the wrong product and I would rather say so before you pay for it than after.
High gloss also shows everything in raking light. In a south facing hallway in Parkville with low winter sun coming across the floor, every footprint reads. We now put a satin topcoat on most residential metallics for exactly that reason, and the handful of high gloss floors we did early on are the ones that get mopped twice as often.
Where is it worth the money?
An entrance. A showroom. One room people walk into and look at. It does the work a piece of commissioned art would do, at a fraction of the price, and nobody else can have the same one.
Where it is not worth it is a working garage. A metallic floor under a car is an expensive surface being asked to do a job a $4 flake floor does better, because flake hides tyre marks and scuffing and metallic does not. We have installed metallics in garages for people who wanted them and they look superb. They also look their age faster.
What makes one metallic floor better than another?
Three things, and none of them are the pigment.
Flatness, first. A self levelling pour sits deeper in every dip, and deeper means darker, so a slab that has never been levelled produces a floor with patches nobody intended. On a garage conversion in an older Kansas City house that is almost always the largest part of the prep.
Second, the working window. Room temperature changes how long the resin stays open, and a cold garage in February gives you less time than a heated interior in May. That is why we would rather pour a metallic indoors or wait for a reasonable week than fight the clock on a cold slab.
Third, the edges. A pour that is worked well in the middle and rushed at the perimeter reads as a good floor with a bad border, and the border is what you see from the doorway.
Can you repair one?
Partly, and this is the honest limit. The clear topcoat can be re-coated over a worn lane without touching the pattern, which is the useful part. A deep gouge that goes through into the pigment cannot be spot repaired invisibly, because the pattern around it cannot be recreated.
We had one in a showroom where a pallet truck was run across a floor that was never specified for it. The repair was a full re-pour of that bay, and it did not match the rest. Metallic is a finish for rooms where that will not happen, and if the room might take that kind of abuse, the right answer is a flake or a quartz system and I will say so.
How long does it last?
The same 10 to 15 years as the rest, because the topcoat takes the wear rather than the pattern. That is the useful part: a worn traffic lane can be re-coated later without touching the pigment underneath, so the thing you paid for is the thing that survives.
The metallic floors page covers how the pour is made, and the finishes page puts all four side by side if you are still deciding.
What to do next
A metallic is the one finish worth seeing in person before you commit. Send the space through the form on this page and Glen calls you back, usually the same working day. He measures on site before anything is final, so the number you get is fixed rather than a range. Or call 816-500-1161, Monday to Friday 7am to 6pm.
Tell us the space. We will price it.
Four questions about the floor, then your details. Glen reads every one of these himself and comes out to measure before anything is final.
- Free, no obligation estimate
- Measured on site, not guessed
- Residential and commercial
- Missouri and Kansas
-
01
You send the space
Type, rough size and what it is used for.
-
02
Glen calls back
Usually the same working day, from the number below.
-
03
He measures on site
Then you get a fixed price, not a range.
Would rather talk it through? Call 816-500-1161, Monday to Friday 7am to 6pm.
Request a Quote
Takes about a minute.